30 channel DMX LED controller dmx decoder& driver and USB DMX PC Controller

Description

Schematic for System Connection:
PC DMX512 Console + USB DMX controller + 30CH DMX deocder
30CH DMX Decoder  Description:
Input Power:  DC9V-DC24V
Maximum load current:  1A/CH×30
Maximum power load: 360W (12V) 720W (24V)
Output gray level: 256
Input Signal:  DMX512/1990
Output signal:  30 channels Constant PWM
Output DMX :  30 channels
standard XLR-3 caron plug
Size:  (L225*W80*H32)/PCS
Gross Weight: (0.3kg)/PCS
Basic functions:
There are 30 output channels, can connect with single or RGB lamps
0-100% dimming output, each channel 256 gray levels
International standard DMX512 input protocol, address code set by DIP switches;
Wide voltage DC input DC9V ~ DC24V;
Each occupied by 30 DMX address.
The decoder comes with 16 kinds of test patterns, 16 levels for rate of change
Decoder to use:
N
ote: FUN = OFF (the tenth code switch up) means to accept DMX512 signal mode
The first DMX address setting:
The decoder set the address bit by coding switch, of which 1-9 is for setting the start address of the Binary numeric code switch of DMX512, the first one is the lowest position,
the ninth one is the highestBit of address code can be set to 255.
DMX512 start address code is the sum of switches 1-9, at the same time turn downside of the code switch (ON set to "1"), then the value of the bit can be gotten; coding switch
up (set to "0"), the value of the bit is 0.
Example 1:
As the following Schematic 1, DMX512 start address is set to 38, encoding the No. 6,3,2 position on switch dial to "1", others set to "0", then the sum of the switch 1-9 code value is
32 + 4 + 2, that is the DMX512 start address 38
(Schematic 1)
Example 2:
As the schematic 2, DMX512 start address is set to 388, encoding the no. 2,3,6,8 switch dial to "1", others set to "0",, then the sum of the switch 1-8 code value is 4 + 128 + 256 = 388,
that is the DMX512 start address 388.
(Schematic 2)
Operation instruction for the automat effect
Note: It will be Automatic operation mode when the No. 10 switch is turned down.
Effect choice (button switch No.1 to No.4):
1, Push No.1: Automat cycling.
2, Push No. 2: Seven-color gradual cycle changing.
3. Push No.1 &2: RGB Fade in and out
4. Push No.3: Severn color jumping
5. Push No.1 & 3: RGB  jumping.
6. Push No.2 & 3: Red color.
7. Push No. 1 & 2 & 3:Green color.
8. Push No.4: Blue color.
9. Push No.1 & 4: Yellow.
10: Push No.2 & 4: Violet.
11. Push No.1 & 2 & 3: Cyan.
12. Push No.3 & 4: white.
13. Push No.1 & 3 & 4: Seven-color gradual cycle changing and jumping.
14. Push No.2 & 3 & rgb-color gradual cycle changing and jumping.
15. Push No.1 & 2 & 3 & 4: Seven-color jumping and rgb-color jumping.
Speed Choices (Button Switch No.5 to No. 8)
1.  Push No.5: 0.5 second. 2. Push No.6: 1 second. 3. Push No.7: 1.5 second. 4. Push No.8: 2 second.
Schematic for System Connection:
If used tow or more power supply, you can connect as  follows:
Installation Notes:
1 This kind of controller works only under DC9V-24V, which is provided by the matched controllable main power, or else the controller will be damaged.
2 The UTP wire is connected hand in hand to make the cable, when two or more controller connected.
3 The power supply should be off when connecting the electric wires, and it can be turned on till making sure the wires are connected correctly and the indicator of main power in red is lighting.
4 Controller should work under the environment of adequately ventilated, dry, not corroded, no flammable gas and rust.
5   Please check the wires connection regularly so that the wires of aged, rust-eaten, and damaged insulation spacer can be replaced timely
Simple troubleshooting and maintenance:
Symptom
Reason Analysis
Solution
NO lighting
1,No power
2,Wrong connection of wire
3,Power protection setting
1,check power supply
2,check wire connection
3,check power failure, power on again
Red indication light is on, green indication light not flash
Didn’t make dip switch or dip switch is not in correct
Follow up the instruction to reset dip switch
The Light color is not show in correctly
1.RGB LED is not connection correctly
2.Dip switch is not in correct place
1, Re-connect the RGB and wire
2, Reset dip switch
Can’t be
synchronization
1,The RJ45 cable is not connected or wrong connection
2, Master and slave controller setting failure,The slaver is set dip switch effects
1, Re-connect the RJ cable
2, Reset master and slave controller to ensure only one master
Led brightness is different at beginning and end
1, Output line is too long
2, The diameter of wire is too thin
3, Overload working
1, Use annular electric supply or shorten circuit
2, Calculate electrical current, change strong wire
3, Change power or increase controller
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
USB DMX  Controller Description:
(1) USB DMX Interface.
(2) Micro processor enabled.
(3)  Supports Various 3rd party softwares.
(4)  Internal frame buffering.
(5)  Drivers for Windows and Linux.
(6) DMX512 times configurable.
Support Windows XP, Vista, Windows 7 (32bit and 64bit)
The signed driver for  Windows XP, Vista and Windows 7.   Besides, on Unix-based operating systems, the LibUSB is integrated directly into the kernel.
Uncompress the file whereever you want and then plugin the hardware.
The operating system will search for a driver.
Select the correct directory (of you uncompression),
After several seconds the driver should be installed
ATTENTION: And then the file uDMX.dll has to be MANUALLY copied to the directory \System32\ in order to finish the installation.
After uDMX.dll has been copied to the directory of \System32\, for example C:\WINDOWS\system32, the driver installation is finished."
Installation:
Download the compressed driver file.
"Advantages of Artnet or why you should use artnet-receiver for X-uDMX512:
Artnet is a network protocol to transfer DMX data over the ip network. Thus it is possible to transfer DMX data with wireless LAN.
Most DMX-Software are able to output DMX-data to Art-Net. So it is not necesary to have a plugin for each program. uDMX can even be used with programs where there is no plugin.
This works for example with:
DMX-Control
Freestyler
Magic Q
Abuelites"
NOTE: It is not compatible with the all dmx Software.
Until now, we know that it can be compatible with the software FreeStyler DMXControl PC-Dimmer, Q Light Controller Vixen Abuelites, MagicQ. If you use other software, please consult us before purchase.
The signed driver for  Windows XP, Vista and Windows 7.   Besides, on Unix-based operating systems, the LibUSB is integrated directly into the kernel.
Packing List:
1 * USB to DMX Interface Adapter
1 * CD
1 * 30CH DMX Decoder